Lynx SmartGrill knob lights sweeping: the grill is starting up
The SmartGrill starts up like a computer.
Mon–Sat, 8am–8pm
- Mode, not a failure
- No repair needed
- Source: Lynx
Book a visit
Three short steps, about a minute.
or call (844) 660-6426
Loading appointment form…
The appointment form couldn’t load. Please try again.
What Knob LEDs sweep back and forth
actually means.
The SmartGrill starts up like a computer. While it boots or loads, the lights around the knobs oscillate so you know it is working, and it answers commands once it is ready.
Lynx grill display
What to do when Knob LEDs sweep back and forth shows on the grillKind of codeMode, not a failure
Nothing on the grill has failed; the controller is showing a state it was put in on purpose. A shutdown cycle keeps the fan running to burn off the last pellets before the grill goes quiet, a keep-warm setting holds the cook box low, a demo mode lights the display without feeding fuel, and a pairing screen waits for a phone to connect. No part is needed; the button sequence in the manual, or simply letting the cycle finish, returns it to normal.
Usually leads toNo repair
Wait for the lights to settle; after a power cycle Lynx allows up to a minute.
Shows up asGrill Error Code on a Pellet Controller or Digital Panel
A grill error code shows as letters and numbers on a pellet grill controller, a flashing light on a digital control panel, or an alert in the maker's app paired with the grill.
MakeLynx
A Lynx grill visit opens with the lid raised and every burner lit once, so the tech sees which ports burn blue and which ones sputter.
SourceSmartGrill by Lynx care and use / installation manual (SMART30, SMART36, SMART42 and F models)
SmartGrill by Lynx built-in and freestanding heads (SMART30, SMART36, SMART42, with F suffix on the cart versions) speak this line through the grill and send the same text to the app. Lynx Professional and Sedona grills with ordinary knobs have no such messages.
Before you book,
in this order.
Each step comes from Lynx's own guidance for Knob LEDs sweep back and forth on its grills. Follow it to the end: the last card says whether this is a visit.
Wait for the lights to settle; after a power cycle Lynx allows up to a minute.
Listen for SmartGrill is ready before pressing the power button.
If the lights keep sweeping for several minutes and the grill never becomes ready, unplug it, plug it back in and book a visit if that does not help.
Cleared?
The code is gone from the controller, the grill climbs to its set heat and holds it through a full cook, the pellets keep dropping and the probe readings stay believable, all without a new part. If the same code comes back within a week, or after the next rain, mention it when you book.
What not to do
Sweeping knob lights are not a warning. A SmartGrill with no knob lights at all is a power problem instead, starting with the plug and the GFCI outlet.
What you may
notice with it.
The grill problems Knob LEDs sweep back and forth tends to arrive with. Answer these at the grill before anyone is booked.
All problems
No repair indicated
Nothing to repair.
Nothing on the grill has failed; the controller is showing a state it was put in on purpose. A shutdown cycle keeps the fan running to burn off the last pellets before the grill goes quiet, a keep-warm setting holds the cook box low, a demo mode lights the display without feeding fuel, and a pairing screen waits for a phone to connect. No part is needed; the button sequence in the manual, or simply letting the cycle finish, returns it to normal.
Lynx
grills.
A Lynx grill visit opens with the lid raised and every burner lit once, so the tech sees which ports burn blue and which ones sputter.
Lynx grill repairMore Lynx codes
Mode, not a failure on other makes
Built-in gas grill
A stainless grill head dropped into a masonry or steel island, fed by a tank or the house gas line, with its burners, knobs and lid working in open weather.
Freestanding gas grill
A gas grill on its own cart with wheels, side shelves and a propane tank below, or a hose to a house gas outlet, rolled into place on the patio.
Infrared grill
Grills that cook with radiant heat: ceramic or mesh infrared burners, sear stations beside the main burners, and radiant glass or emitter plates over a gas flame.
In Lynx's own words
Any time the grill is loading or booting, the knob LEDs will oscillate back and forth letting you know the grill is busy.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. SmartGrill by Lynx built-in and freestanding heads (SMART30, SMART36, SMART42, with F suffix on the cart versions) speak this line through the grill and send the same text to the app. Lynx Professional and Sedona grills with ordinary knobs have no such messages.
Lynx Knob LEDs sweep back and forth grill repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about Knob LEDs sweep back and forth.
Can I clear Knob LEDs sweep back and forth myself?
How long do the Lynx SmartGrill knob lights sweep when I turn it on?
Can I turn a SmartGrill knob while the lights are sweeping?
My SmartGrill knob lights are dark. Is that the same thing?
Back to your everyday
Still showing Knob LEDs sweep back and forth?
A booking with a code goes further when it has the code copied exactly, the model and serial from the rating label, and a word on whether the grill still lights, heats or feeds pellets. With those three the office can match the likely part to your grill the same day.