Lynx SmartGrill "Igniter failed to start": a glow igniter is not heating
SmartGrill heads light their burners with glowing hot-surface igniters rather than a spark.
Mon–Sat, 8am–8pm
- Ignition
- Grill igniter repair
- Source: Lynx
Book a visit
Three short steps, about a minute.
or call (844) 660-6426
Loading appointment form…
The appointment form couldn’t load. Please try again.
What Igniter failed to start
actually means.
SmartGrill heads light their burners with glowing hot-surface igniters rather than a spark. This message means the controller did not see the igniter for the named burner come up to heat, and it shuts that burner down instead of letting unburned gas flow.
Lynx grill display · also shown as Burner N igniter malfunctioned, Igniter Failure
What to do when Igniter failed to start shows on the grillKind of codeIgnition
The grill tried to start its fire and the controller never saw it take. On a pellet grill that is usually a hot rod burned out after hundreds of cooks, or a firepot full of ash so the new pellets smother; on a gas grill with electronic ignition it is a spark module, an electrode cracked or set too far from the burner, or a battery gone flat. Emptying the ash once the grill is cold and fitting a fresh battery are fair first steps; the hot rod and the module are a visit.
Usually leads toGrill igniter repair
No spark, a weak spark or a spark in the wrong place: the grill's battery module, piezo button, electrodes, wires and hot-surface igniters tested and fixed.
Shows up asGrill Error Code on a Pellet Controller or Digital Panel
A grill error code shows as letters and numbers on a pellet grill controller, a flashing light on a digital control panel, or an alert in the maker's app paired with the grill.
MakeLynx
A Lynx grill visit opens with the lid raised and every burner lit once, so the tech sees which ports burn blue and which ones sputter.
SourceSmartGrill by Lynx care and use / installation manual (SMART30, SMART36, SMART42 and F models)
SmartGrill by Lynx built-in and freestanding heads (SMART30, SMART36, SMART42, with F suffix on the cart versions) speak this line through the grill and send the same text to the app. Lynx Professional and Sedona grills with ordinary knobs have no such messages.
Before you book,
in this order.
Each step comes from Lynx's own guidance for Igniter failed to start on its grills. Follow it to the end: the last card says whether this is a visit.
Turn every burner off and check that the gas shutoff or tank valve is open.
Wait five minutes so any gas in the firebox clears before you try that burner again.
Lift a grate and watch the igniter for about a minute with the knob on; if it never glows orange, stop there and book a visit so the igniter and its wiring can be tested.
What not to do
This is not the same as a burner that lit and then went out, which SmartGrill reports as no flame or failed to stabilize. It also does not mean the whole grill has lost power, because the knob lights and the voice would be silent in that case.
What you may
notice with it.
The grill problems Igniter failed to start tends to arrive with. Answer these at the grill before anyone is booked.
All problems
Where Igniter failed to start usually leads
Grill igniter repair.
Lynx
grills.
A Lynx grill visit opens with the lid raised and every burner lit once, so the tech sees which ports burn blue and which ones sputter.
Lynx grill repairMore Lynx codes
Ignition on other makes
All 5 codes of this kind
Built-in gas grill
A stainless grill head dropped into a masonry or steel island, fed by a tank or the house gas line, with its burners, knobs and lid working in open weather.
Freestanding gas grill
A gas grill on its own cart with wheels, side shelves and a propane tank below, or a hose to a house gas outlet, rolled into place on the patio.
Infrared grill
Grills that cook with radiant heat: ceramic or mesh infrared burners, sear stations beside the main burners, and radiant glass or emitter plates over a gas flame.
In Lynx's own words
Text: "Igniter failed to start."
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. SmartGrill by Lynx built-in and freestanding heads (SMART30, SMART36, SMART42, with F suffix on the cart versions) speak this line through the grill and send the same text to the app. Lynx Professional and Sedona grills with ordinary knobs have no such messages.
Lynx Igniter failed to start grill repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about Igniter failed to start.
Can I clear Igniter failed to start myself?
Why is there no clicking before my Lynx SmartGrill shows Igniter failed to start?
Can I light a SmartGrill burner with a match after Igniter failed to start?
Does one bad igniter stop the whole Lynx SmartGrill?
Back to your everyday
Still showing Igniter failed to start?
A booking with a code goes further when it has the code copied exactly, the model and serial from the rating label, and a word on whether the grill still lights, heats or feeds pellets. With those three the office can match the likely part to your grill the same day.